Lee 38 Special / 357 Magnum Pistol 3-Die Set includes Carbide Full Length Sizing Die, Powder Through Expanding Die, Bullet Seating Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data.
Note: You may use the 38 Special die set to reload for the 357 Magnum and 357 Maximum. You would have to back out the Powder Thru Expander Die, and the Bullet Seating and Crimping Die about 2 turns to compensate for the longer 357 Magnum case, additional adjustments needed for 357 Maximum.
Proven design with compound leverage. No spring in this turret design. The turret is locked into a solid steel ring with big rifle bolt type lugs. Patented design puts the lugs on the circumference so there can be no tipping. The linkage is so powerful that the largest magnum cases are sized with ease. Effort required is so small that the usual heavy bench is not essential. The Lee Turret Press has built-in primer catcher, longer stroke, more hand clearance and a comfortable wood grip. Even if you do not need all of these features, why pay more for anything less? In fact, you will want a Lee Turret Press even if you already own a more expensive one.
The fourth hole in the turret allows you to install your Lee Factory Crimp Die or Taper Crimp Die in the press.
The auto index on the Value Turret Press is capable of loading cartridges with an overall length of 2.313" or less. Our Classic Turret Press also has the auto index feature, and is capable of loading cartridges with an overall length of 3.313" or less. For both presses anything longer than the above specs, would require the turret to be manually advanced.
* Table not included with the machine as per picture.
4 hole Ultimate Tool Carrier and 4 hole Index Rod for the Ultimate Turret Press (product # 91910), or Ultimate Turret Press Kits. The round tool carrier is precision machined on all surfaces.
5 hole turret and index rod for the Ultimate Turret Press or Ultimate Turret Press Kits. The round tool carrier is precision machined on all surfaces. Each die position is machined to accept any Lee Breech lock bushing
Lee 9mm Makarov Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability. This die applies a taper crimp. The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
Part PT2970 Connecting Rod for product NEW AUTO PRIME (Code=90230) and AUTO BENCH PRIME (Code=90700).
Note: this part will not fit the original Auto-Prime with the round primer trays.
The Lee App Bulge Buster Kit and the appropriate Lee Carbide Factory Crimp Die, restore free function of rimless cases that have low base bulges. Low base bulges usually occur from chambers that do not fully support the cartridge or cases resized in carbide dies from manufacturers other than Lee. These show a noticeable stop ring near the base. You will most likely find cases with these problems in mixed range brass.
** Will only work with the following cases: 380 ACP, 10mm, 40 S&W, 41 AE (Use 40 S&W Factory Crimp Die), 45 ACP, 45 GAP, and 45 Win Mag.
The Lee Carbide Factory Crimp Die must be purchased separately, see website for stock.
The Lee Deluxe Automatic Processing Press gives you the same priming convenience found only on expensive progressive reloading presses.
We started with the basic APP, added the Roller Handle, Universal Case Feed Magazine and the APP Deprime kit. Then we fitted the tool with the Patented automatic primer feed system. There is no priming system made that is as fast, effortless, or uniform as the APP primer. Cases and primers are automatically fed. Primers are seated uniformly without "feel" or adjustments required. Safe with any brand or size of primer. Change primer size in seconds. Simply twist out the priming chamber and swap out the pin and primer guide. No shell holders required! When you’re finished priming — simply twist out the priming tool and replace with the supplied shell holder adapter. Then you can use all the APP accessories available to Bulge Bust or Primer Pocket Swage.
Includes:
Press
Roller Handle
Priming System
Universal 4 Tube Case Feeder
APP Deprime Kit
Bottle Adapter
Photo note: The mount is not included and can be purchased sperately.
Maximum case legnth is 30-06 or 2.494" to process cases
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.
